FAQ

CTi of Acadiana, LLC offers a 3-year limited material warranty against dramatic fading, delamination, and general product failure. 

Yes! Through an arrangement with Acorn Finance you can buy now and pay monthly. You can pre-qualify and receive funds as early as 1-2 business days. Click here to learn more.

CTi’s systems are thin layered cements which depend on adhesion through the use of modified acrylics. We generally apply our systems on old concrete adding between 3/32″ to 1/8″ to the current surface.

CTI’s systems achieve a look, texture, and color of any type stone or look you require. A base coat is applied that covers any imperfections in the original concrete. A design is then laid over it and a hopper gun shoots on a textured layer over that. A final clear coat is put over the system that is nonporous and protects it as well as makes it very easy to maintain. Mold, mildew, motor oil, etc. can be sprayed off with a regular garden hose. Common detergents can be used to remove tough or repetitive latencies. Visit our portfolio tab for examples.

No, the pool should be full. If the pool were empty, the CTi system overspray would stain the plaster. Full, any small amount of overspray can be dealt with by allowing the overspray to settle to the bottom, shutting off the filter, then pumping the material to waste and bypassing all filters is recommended.

We have a variety of standard colors to choose from. However, we can custom produce any color you wish for a minimal extra charge.

An average project takes 3 to 4 days. Larger, more complex jobs, may take longer. Clean foot traffic is usually allowed within the same day.

All existing control joints should remain in the surface to allow for expansion and contraction of the original concrete. They are not coated with the CTi system and are masked off. We can, however, work to ensure these joints match the rest of the look of the surfaces.

No. Kool Deck® is a product that must be applied to freshly poured concrete within 5 hours in order to bond. CTI’s systems can be applied to new or old concrete. In addition, CTI’s systems are a three-coat system and are sealed with a finish coat, which makes it impervious to staining. Whereas Kool Deck® is a very porous, non-flexible product, that has a minimal life expectancy.

No, the sealers we apply to our system is not affected by most chemicals.

No, not dramatically, the CTI product has approximately a 2% fade factor over seven years, which is undetectable by the human eye; our warranty covers this.

We can generally improve drainage; however, the degree of success is contingent upon the pitch of the concrete adjacent to the low spot. The low spot will have to be looked at personally by an authorized CTI dealer to let you know what you can expect.

Cracks are ground out with a cup grinder to produce a “V”. A two-part epoxy with a chopped fiberglass filament is then introduced into the crack and will re-bond the crack.

Though we do everything possible to treat cracks and do eliminate 90% of them, it is possible they may reoccur. If they do, it is usually in the form of a hairline, which is not objectionable as it is largely hidden in the texture. However, if a crack becomes too objectionable, it is easy to repair. Proper placement of tension cuts greatly reduces the chance of the crack returning. Check cracking is a natural phenomenon which occurs in rock, dried-out mud flats, paint, and concrete and in ceramic coatings. Cracks in the concrete may be structural or surface cracks. Surface cracks are generally less than a few millimeters wide and deep. These are often called hairline or check cracks and may consist of single, thin cracks, or cracks in a craze/map-like pattern. A small number of surface or shrinkage cracks is common and does not usually cause any problems. Surface cracks can be caused by freezing and thawing, poor construction practices, and alkali-aggregate reactivity. Alkali-aggregate reactivity occurs when the aggregate reacts with the cement causing crazing or check cracks. Structural cracks in the concrete are usually larger than .1/8 inch in width. They extend deeper into the concrete and may extend all the way through a wall, slab, or other structural member. Structural cracks are often caused by settlement of the fill material supporting the concrete structure, or by loss of the fill support due to erosion. The structural cracks may worsen in severity due to the forces of weathering.

The material is repairable to its original state. We service all decks past warranty.

Yes, though it generally will need to be scarified or sandblasted to remove the paint enough to where our product will bond with the original concrete.

Yes, CTI’s systems can be applied to concrete steps including risers and treads.

Yes, however, multiple spray coats are needed to reduce rebound, or waste.

We do apply CTI’s systems to cantilever faces and coping stones. Though application over coping stones is a matter of personal preference, it is often advisable to coat the stones unless they are exceptionally new. If not coated, they tend to look old and dirty after the CTI installation is complete. In addition, the older copings which have deep lips can be filled in so the coping stones are level with the deck giving a modern cantilevered look.

No, CTI’s systems are feathered very thin at the joint edge so the coping and decking will be level.

Acrylic decking has been in use since the early 70’s. Our manufacturing facility has been producing coatings since 1968.

Yes, quite easily.

The cost of the CTI system is normally 20%-25% less than the cost of removing cement and pouring new and is much better looking and much easier to maintain than the original cement.

The price depends on a number of factors, such as the condition of the original concrete, the patterns chosen, etc. This is why we offer a free estimate appointment to determine all of these factors.

Usually, normal washing with a hose is all that is needed. For stubborn stains, a brush with laundry detergent is all that is needed.

CTi’s systems are harder than concrete. Most concrete has a compressive strength of 2000-2500 psi rating. CTi’s system has a 7000 psi rating.

While concrete floors are relatively easy to maintain, compared with other types of floor surfaces, they aren’t completely maintenance free. How much maintenance your floor will need largely depends on the amount of traffic it receives. The maintenance needs of a residential floor will be much different than those for a floor in a high-traffic commercial or retail environment. In most cases, residential floors experience light foot traffic, and a simple cleaning regimen of occasional sweeping and damp mopping will keep concrete floors looking like new for many years. Protecting concrete floors with a good sealer and a coat of floor finish or wax will make them even more resistant to stains, chemicals and abrasion. In areas of heavy traffic, such as entrances and foyers, you can reduce maintenance and wear and tear by using floor mats, both inside and outside of the entryways.

When compared with high-end floor coverings, such as ceramic tile, slate and marble, decorative concrete is often an economical alternative. Plus, skilled concrete artisans can duplicate the look of these pricier materials. The life expectancy of a concrete floor will also far surpass that of low- to mid-priced floor coverings, such as carpeting, vinyl tile and wood laminates. That means in the long run you can save money because you’ll never need to rip out and replace worn or damaged flooring.

Concrete is a hard material, so it won’t cushion or “give” under bare feet. But concrete’s hardness is also what contributes to its durability and abrasion resistance. In a commercial or warehouse setting, hard is good. You need a hard surface that can stand up to forklift traffic and heavy foot traffic. For a residential floor, you can help cushion concrete with area rugs, which are easier to clean than wall-to-wall carpet. While concrete may be hard, it’s not abrasive to the feet, especially if it’s polished or has a smooth finish.

A concrete overlay is a thin color concrete cement based product that goes over existing concrete for repair or decorative reasons. Overlays can be applied as thin as a feather finish up to in most cases 3/4″ depending on the desired finish. Concrete overlays, however, are only as good as the substrate it is being applied over. For example, if the concrete is cracked or coming up, the overlay will also break and come up.